D-Link DAP-1160 rev A1
Jump to navigation
Jump to search
D-Link DAP-1160 A1
Manuf (OEM/ODM): Cameo
Type: access point
FCC ID: KA2AP1160A1
IC ID: 4216A-AP1160
Power: 5 VDC, 2 A
Connector type: barrel
CPU1: Realtek RTL8186
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Macronix MX29LV320CBTC-70G)
RAM1: 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (EtronTech EM639165TS-6G)
Expansion IFs: none specified
Serial: yes, 4-pin header, (38400,8,N,1)
WI1 chip1: Realtek RTL8186
WI1 chip2: Realtek RTL8225
WI1 802dot11 protocols: bg
WI1 antenna connector: RP-SMA
ETH chip1: Realtek RTL8186
ETH chip2: Realtek RTL8201CP
ETH chip3: Realtek RTL8201CP
LAN speed: 100M
LAN ports: 2
bg
Stock FW OS: Linux 2.4.18-MIPS-01.00
Default IP address: 192.168.0.50
the IP 192.168.0.50 is used by 63 additional devices
of which 63 are D-Link devices
Default login user: admin
Default login password: blank
admin:blank credentials used by 344 additional devices
of which 180 are D-Link devices
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Wireless G Access Point
Product page (UK)
Listed on Realtek SOC page on linux-mips.org as having 4MB Flash and 16MB RAM.
Wi-Fi Certified : WFA4957 (as of 02/15/2007)
JTAG
Located at J2
To make JTAG work, R68 should be added.
UART
Located at J1 : [Vcc|TX|RX|GND]
Baudrate 38400 8M1
Images
the unit
Logs
UART1 output test ok
Uart init
mfid=000000c2 devid=000022a8
Found 1 x 4M flash memory
---RealTek(RTL8186)at 2007.07.05-16:20+0800 version 1.4a , CAMEO version v1.00.r06 [16bit](180MHz)
no sys signature at 00010000!
no sys signature at 00020000!
Jump to image start=0x80300000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initial ramdisk at: 0x801aa000 (1015651 bytes)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 179.40 BogoMIPS
Memory: 13244k/16384k available (1533k kernel code, 3140k reserved, 1092k data, 56k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 5120K size 1024 blocksize
PPP generic driver version 2.4.1
PPP MPPE Compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 4M Byte MXIC MX29LV320AB at 0xbe000000
RTL8185 driver version 1.14 (2008-02-15)
8186NIC Ethernet driver v0.0.8 (Jan 30, 2007)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
Realtek FastPath v1.02
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 991k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 56k freed
mount /proc file system ok!
serial console detected. Disabling virtual terminals.
init started: BusyBox v1.00-pre8 (2007.04.16-08:33+0000) multi-call binary
BusyBox v1.00-pre8 (2007.04.16-08:33+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
killall: led_shine.sh: no process killed
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
Initialize wlan0 interface
Using wlan script...
Setup BRIDGE interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
br0: topology change detected, propagating
eth0:phy is 8201
SIOCDELRT: No such process
device eth1 entered promiscuous mode
eth1:phy is 8201
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
device wlan0-vxd entered promiscuous mode
SIOCDELRT: No such process
br0: port 4(wlan0-vxd) entering listening state
br0: port 3(wlan0) entering listening state
br0: port 2(eth1) entering listening state
br0: port 1(eth0) entering listening state
SIOCDELRT: No such process
SIOCDELRT: No such process
SIOCDELRT: No such process
br0: port 4(wlan0-vxd) entering learning state
br0: port 3(wlan0) entering learning state
br0: port 2(eth1) entering learning state
br0: port 1(eth0) entering learning state
Setup Firewall
br0: port 4(wlan0-vxd) entering forwarding state
br0: topology change detected, propagating
br0: port 3(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
auth uses obsolete (PF_INET,SOCK_PACKET)
IEEE 802.1x (WPA) daemon, version 1.7f
IEEE 802.1x (WPA) daemon, version 1.7f
killall: reload: no process killed
br0: bridge ip(c0a80032)!
killall: led_shine.sh: no process killed
killall: dccd: no process killed
killall: watchdog.sh: no process killed
killall: tftpd: no process killed
743
# preset:5ef set:4e7
End ledshine!
Built-in commands:
-------------------
. : break cd continue eval exec exit export help login newgrp
read readonly set shift times trap umask wait
#cat /proc/
/proc/1/ /proc/enable_dos /proc/nat_ipsec
/proc/2/ /proc/eth_flag /proc/nat_l2tp
/proc/3/ /proc/execdomains /proc/net/
/proc/4/ /proc/fast_l2tp /proc/partitions
/proc/5/ /proc/fast_nat /proc/pptp
/proc/6/ /proc/fast_pptp /proc/qos
/proc/600/ /proc/fdb_max /proc/rf_switch
/proc/611/ /proc/filesystems /proc/rx_pkt_thres
/proc/622/ /proc/fs/ /proc/self/
/proc/7/ /proc/gpio /proc/slabinfo
/proc/708/ /proc/iomem /proc/stat
/proc/710/ /proc/ioports /proc/swaps
/proc/724/ /proc/kcore /proc/sys/
/proc/745/ /proc/kmsg /proc/tty/
/proc/8/ /proc/led_gpiopabdata /proc/uptime
/proc/br_igmpsnoop /proc/load_default /proc/url_filter
/proc/bus/ /proc/loadavg /proc/version
/proc/cmdline /proc/locks /proc/wlan0-vxd/
/proc/cpuinfo /proc/meminfo /proc/wlan0/
/proc/devices /proc/misc /proc/wlan_iflife
/proc/dma /proc/mounts /proc/wlan_led
/proc/driver/ /proc/mtd
#cat /proc/cpuinfo
system type : Philips Nino
processor : 0
cpu model : R3000 V0.0
BogoMIPS : 179.40
wait instruction : no
microsecond timers : no
tlb_entries : 64
extra interrupt vector : no
hardware watchpoint : no
VCED exceptions : not available
VCEI exceptions : not available
ll emulations : 0
sc emulations : 0
# cat /proc/version
Linux version 2.4.18-MIPS-01.00 (root@localhost.localdomain) (gcc version 3.3.3) #2 \A4T 7\A4\EB 15 14:49:34 CST 2009
# cat /proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 14635008 10256384 4378624 0 180224 6979584
Swap: 0 0 0
MemTotal: 14292 kB
MemFree: 4276 kB
MemShared: 0 kB
Buffers: 176 kB
Cached: 6816 kB
SwapCached: 0 kB
Active: 1024 kB
Inactive: 6564 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 14292 kB
LowFree: 4276 kB
SwapTotal: 0 kB
SwapFree: 0 kB
