Netgear WAC104

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Netgear WAC104 -100NAS
Availability: common

Manuf (OEM/ODM): SerComm

FCC approval date: 07 October 2014
Country of manuf.: China

Amazon image

ASIN
B01LFSDZCU (Flag of the United States.svg, On Amazon, On CCC)

Type: access point

FCC ID: PY314200274
IC ID: 4054A-14200274
PCB ID: AYA00B-1.6MM

Power: 12 VDC, 1.5 A

CPU1: MediaTek MT7621ST (880 MHz)
FLA1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Macronix MX30LF1G08AA-TI)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Nanya NT5CB64M16FP-DH)

Expansion IFs: none specified
Serial: yes, 4-pin header, J4

WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: none

ETH chip1: MediaTek MT7621ST
Switch: MediaTek MT7621ST
LAN speed: 1GbE
LAN ports: 4

abgn+ac

Stock bootloader: U-Boot 1.1.3 Ralink 4.2.1.0

Stock FW OS: Linux 2.6.36

TPFirmware supported: OpenWrt • (List | Dev | DLs)

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1303 additional devices
of which 106 are Netgear devices
Default login user: admin
Default login password: password
admin:password credentials used by 423 additional devices
of which 304 are Netgear devices

802dot11 OUI: DC:EF:09 (1 E, 1 W)
Ethernet OUI: DC:EF:09 (1 E, 1 W)

 FCC ID
Netgear R6220PY314200274
Netgear R6230PY314200274
Netgear WNDR3700v5PY314200274
PY314200275

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.


AC1200 Wireless Dual Band Access Point

Product page

"AYA00B-1.6MM" is silkscreened on the board in the images.

Firmware

 • bootlog • >>
 ===================================================================
                MT7621   stage1 code 13:15:05 (ASIC)
                CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xd, 1/0 = 556/468 35000000
PLL2 FB_DL: 0x10, 1/0 = 688/336 41000000
PLL4 FB_DL: 0x13, 1/0 = 696/328 4D000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000E:|    0    0    0    0    0    0    0    0    0    0    1    1    1    1    1    1
000F:|    0    0    0    0    0    1    1    1    1    1    1    1    1    1    1    0
0010:|    1    1    1    1    1    1    1    1    1    1    0    0    0    0    0    0
0011:|    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 16
rank 0 fine = 40
B:|    0    0    0    0    0    0    0    0    0    0    1    1    1    0    0    0
opt_dle value:11
DRAMC_R0DELDLY[018]=00001F20
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    13 7 12 9 13 7 13 5 3 11
10 |    7 15 7 12 7 11
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =32 DQS1 = 31
==================================================================
bit     DQS0     bit      DQS1
0  (1~58)29  8  (1~55)28
1  (1~56)28  9  (1~56)28
2  (1~58)29  10  (2~60)31
3  (1~58)29  11  (2~58)30
4  (1~60)30  12  (1~59)30
5  (1~56)28  13  (1~56)28
6  (2~62)32  14  (1~58)29
7  (1~60)30  15  (2~58)30
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    15 11 15 12 15 11 13 7 6 14
10 |    7 15 8 15 9 12
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0801
DQS loop = 14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=14,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=14,  finish count=2
DQ loop=15, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=1
DQ loop=14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=14,  finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=50000000 HZ BUS=16666666 HZ
===================================================================


U-Boot 1.1.3 (Sep 25 2015 - 10:29:47)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87fac000

Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 87fe1bb0
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device found in MTK table, ID: c2f1, EXT_ID: 809502
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8
Env addr : 0x100000
.*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC MT7621AS (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Sep 25 2015  Time:10:29:47
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 880 MHZ ####
 estimate memory size =128 Mbytes

Reset switch ...
#Reset_MT7530
set LAN/WAN LLLLW
..Example expects ABI version 2
Actual U-Boot ABI version 2

******************************************
    Uboot StandAlone Entry
******************************************
0, cmd
1, 0x0000000D
cmd : 0x0000000D


Press Ctrl+C to Enter the Main loop...
Example expects ABI version 2
Actual U-Boot ABI version 2

******************************************
    Uboot StandAlone Entry
******************************************
0, cmd
1, 0x0000000F
cmd : 0x0000000F
Enter NMRP_main
Flash Sector Number : 1024.

 NetTxPacket = 0x87FE5B40

 KSEG1ADDR(NetTxPacket) = 0xA7FE5B40

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 ETH_STATE_ACTIVE!!
NMRP_FLASH_SIZE_buffer --> a1000000.
NMRP:LISTENING
### No NMRP Server found ###

 KSEG1ADDR(NetTxPacket) = 0xA7FE5B40

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 ETH_STATE_ACTIVE!!
STANDALONE_LOAD_ADDR is 0xa0600000
Example expects ABI version 2
Actual U-Boot ABI version 2

******************************************
    Uboot StandAlone Entry
******************************************
0, boot
Flash Sector Number : 1024.

***************************************************
    Sercomm Boot Version 1.19.0

***************************************************
Upgrade flag check pass!Entering Firmware : Everything is OK.
kernel addr :0xbfe00000

 System Boot system code via Flash.
## Booting image at bfe00000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2525365 Bytes =  2.4 MB
   Load Address: 80001000
   Entry Point:  8000f500
.......................................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK



commandline in boot is : <NULL>  !!!!



No initrd
## Transferring control to Linux (at address 8000f500) ...
## Giving linux memsize in MB, 128

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Fri Sep 29 01:51:39 CST 2017

 The CPU feqenuce set to 880 MHz
GCMP present
CPU revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
avail: cpu2 is not ready
avail: cpu3 is not ready
Detected 1 available secondary CPU(s)
PERCPU: Embedded 7 pages/cpu @81103000 s7104 r8192 d13376 u65536
pcpu-alloc: s7104 r8192 d13376 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 console=ttyS0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Writing ErrCtl register=0004f507
Readback ErrCtl register=0004f507
Memory: 122252k/131072k available (5385k kernel code, 8820k reserved, 1699k data, 216k init, 0k highmem)
Hierarchical RCU implementation.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Trying to install interrupt handler for IRQ24
Trying to install interrupt handler for IRQ25
Trying to install interrupt handler for IRQ22
Trying to install interrupt handler for IRQ9
Trying to install interrupt handler for IRQ10
Trying to install interrupt handler for IRQ11
Trying to install interrupt handler for IRQ12
Trying to install interrupt handler for IRQ13
Trying to install interrupt handler for IRQ14
Trying to install interrupt handler for IRQ16
Trying to install interrupt handler for IRQ17
Trying to install interrupt handler for IRQ18
Trying to install interrupt handler for IRQ19
Trying to install interrupt handler for IRQ20
Trying to install interrupt handler for IRQ21
Trying to install interrupt handler for IRQ23
Trying to install interrupt handler for IRQ26
Trying to install interrupt handler for IRQ27
Trying to install interrupt handler for IRQ28
Trying to install interrupt handler for IRQ15
Trying to install interrupt handler for IRQ8
Trying to install interrupt handler for IRQ29
Trying to install interrupt handler for IRQ30
Trying to install interrupt handler for IRQ31
console [ttyS1] enabled
Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Brought up 2 CPUs
Synchronize counters across 2 CPUs: done.
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8

*************** MT7621 PCIe RC mode *************
PCIE1 no card, disable it(RST&CLK)
pcie_link status = 0x5
RALINK_RSTCTRL= 5000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 12007f2
PCIE0 enabled
PCIE2 enabled
interrupt enable status: 500000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x60300000-0x6030ffff] (PCI address [0x60300000-0x6030ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
pci 0000:00:01.0: BAR 1: set to [mem 0x60310000-0x6031ffff] (PCI address [0x60310000-0x6031ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff] (PCI address [0x60200000-0x602fffff]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
pci 0000:00:01.0:   bridge window [mem pref disabled]
PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60300000
res[1]->end = 6030ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60310000
res[1]->end = 6031ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]->start = 60000000
res[0]->end = 600fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x2, slot = 0x1, irq=0x19
res[0]->start = 60200000
res[0]->end = 602fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1171456)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 238
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
spidrv_major = 217
i2cdrv_major = 218
spdif_mod_init: start SPDIF module
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
brd: module loaded
MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
Allocate 16 byte aligned buffer: 80753d20
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02, 00809502]
Device found in MTK table, ID: c2f1, EXT_ID: 809502
Support this Device in MTK table! c2f1
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Scanning device for bad blocks
Signature matched and data read!
load_fact_bbt success 1023
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Creating 22 MTD partitions on "MT7621-NAND":
0x000000000000-0x000000100000 : "Bootloader"
0x000000100000-0x000000200000 : "SC PID"
0x000000200000-0x000000600000 : "Kernel"
0x000000600000-0x000002200000 : "Rootfs"
0x000002200000-0x000002400000 : "English UI"
0x000002400000-0x000002600000 : "ML1"
0x000002600000-0x000002800000 : "ML2"
0x000002800000-0x000002a00000 : "ML3"
0x000002a00000-0x000002c00000 : "ML4"
0x000002c00000-0x000002e00000 : "ML5"
0x000002e00000-0x000002f00000 : "Factory"
0x000002f00000-0x000003000000 : "SC Private Data"
0x000003000000-0x000003200000 : "POT"
0x000003200000-0x000003400000 : "Traffic Meter"
0x000003400000-0x000003600000 : "DPF"
0x000003600000-0x000003800000 : "SC Nvram"
0x000003800000-0x000003a00000 : "Ralink Nvram"
0x000003a00000-0x000003c00000 : "Ralink Reserved"
0x000003c00000-0x000003e00000 : "ML6"
0x000003e00000-0x000004000000 : "Upgrade Flag"
0x000004000000-0x000004200000 : "Reserved Block3"
0x000004200000-0x000007e00000 : "Reserved Block4"
[mtk_nand] probe successfully!
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x4328804b
Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288022
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
usbcore: registered new interface driver net1080
register mt_drv


=== pAd = c0182000, size = 703704 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
device_id =0x7603
RtmpChipOpsHook(502): Not support for HIF_MT yet!
mt7603_init()-->
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<--mt7603_init()
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Ralink APSoC Hardware Watchdog Timer
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1910 buckets, 7640 max)
nf_conntrack_rtsp v0.6.21 loading
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
L2TP IP encapsulation support (L2TPv3)
L2TP netlink interface
L2TP ethernet pseudowire support (L2TPv3)
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 216k freed
init started: BusyBox v1.12.1 (2017-09-29 01:59:38 CST)
starting pid 62, tty '': '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mount: mounting none on /dev/pts failed: No such file or directory
/usr/etc/rcS: /etc/PROJECT.mak: line 111: 3G_FEATURE=0: not found
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

[rc debug]/sbin/rc reg_init
[rc.c::configure_mt7621_register():1037] set from jtag to gpio mode
[SYSTEM]/sbin/reg switch register base addr to system register 0xbe000000
s 0
[SYSTEM]/sbin/reg r0xa05a9
 0x60
[SYSTEM]/sbin/reg write offset 0x60, value 0xa05a8
w 0x60 0xa05a8
[SYSTEM]/sb0xa05a8
in/reg r 0x60
[SYSTEM]/bin/echo 1 > /NOTIFY
prNOTIFY
ocNOTIFY
/NOTIFY
sNOTIFY
ysNOTIFY
/NOTIFY
net/ipv6/conf/all/disable_ipv6
led_pb_api: module license 'Sercomm' taints kernel.
Disabling lock debugging due to kernel taint
Register LED ID <75>
Register LED ID <70>
Register LED ID <45>
Register LED ID <40>
Register LED ID <20>
Register LED ID <60>
Register LED ID <61>
Register LED ID <62>
Register LED ID <90>
Register LED ID <91>
Register LED ID <92>
insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko': No such file or directory
insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/ext4/ext4.ko': No such file or directory
netfilter dnshj choose interested dns queries module loaded !
insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory
init common module successful
insert firewall block module success
fake source dos protect modules is inserted
netfilter PSD and TCP/UDP Echo/Chargen Attack loaded
netfilter tcp syn flood module loaded
netfilter clamp total session for one src ip module loaded
netfilter other dos module loaded
insmod finish
NOTIFY
NOTIFY
NOTIFY
Raeth v3.1 (Tasklet,SkbRecycle)

phy_tx_ring = 0x06e92000, tx_ring = 0xa6e92000

phy_rx_ring0 = 0x06e94000, rx_ring0 = 0xa6e94000
change HW-TRAP to 0x15c8f
set LAN/WAN LLLLW
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288022
GDMA2_MAC_ADRH -- : 0x0000000c
GDMA2_MAC_ADRL -- : 0x43288028
NOTIFY
NOTIFY
eth3: ===> VirtualIF_open
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
NOTIFY
NOTIFY
NOTIFY
insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko': No such file or directory

register rt2860


=== pAd = c0982000, size = 1142784 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0880000, csr_addr=0xc0880000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
====> mt76x2_ePA_per_rate_compensate_init: 5118 is_ePA: 1
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is FLASH mode
NOTIFY
NOTIFY
[rc debug]/usr/sbin/rc init
[SYSTEM]/sbin/ifNOTIFY
cNOTIFY
onNOTIFY
fig br0 down hw ether 14:59:C0:C3:DF:88 up
[SYSTEM]/sbin/ifconfig eth2.1 down
ifconfig: SIOCGIFFLAGS: No such deNOTIFY
vice
[SYSTEM]/sbin/ifconfig eth2.2 down
ifconfig: SIOCGIFFLAGS: No suchra2880stop()... Done
deeth3: ===> VirtualIF_close
Free TX/RX Ring Memory!

OTIFY
32m[SYSTEM]/sbin/ifconfig eth2 down
[SYSTEM]/sbin/vconfig rem eth2.1
vconfig: ioctl error for rem: No such device
[SYSTENOTIFY
MRaeth v3.1 (]Tasklet/,SkbRecycles)
bin
phy_tx_ring = 0x0665e000, tx_ring = 0xa665e000
/vconfi
phy_rx_ring0 = 0x06654000, rx_ring0 = 0xa6654000
g rem eth2.2
vconfig: ioctl error for rem: No such device
[change HW-TRAP to 0x15c8f
SYSTEM]/sbinset LAN/WAN LLLLW
MAC1_MAC_ADRH -- : 0x0000000c
0GMAC1_MAC_ADRL -- : 0x43288022
eth3: ===> VirtualIF_open

CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
NOTIFY
[SYSTEM]/sbin/ifconfigNOTIFY
 eth2 down
ra2880stop()...Done
eth3: ===> VirtualIF_close
Free TX/RX Ring Memory!
NOTIFY
[SYSTEM]/sbin/ifconfigNOTIFY
NOTIFYhw ether 14:59:C0:C3:DF:88
            asklet3,SkbRecycle2)
m[S
phy_tx_ring = 0x06f5a000, tx_ring = 0xa6f5a000
YSTEM]/
phy_rx_ring0 = 0x06f5c000, rx_ring0 = 0xa6f5c000
sbin/ifconfig eth2 up
change HW-TRAP to 0x15c8f
set LAN/WAN LLLLW
GMAC1_MAC_ADRH -- : 0x00001459
GMAC1_MAC_ADRL -- : 0xc0c3df88
eth3: ===> VirtualIF_open
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
NOTIFY
[SYSTEM]/usr/sbin/config-vlan.sh 3 0
restore GSW to dump switch mode
switch reg write offset=2004, value=ff0000
switch reg write offset=2104, value=ff0000
switch reg write offset=2204, value=ff0000
switch reg write offset=2304, value=ff0000
switch reg write offset=2404, value=ff0000
switch reg write offset=2504, value=ff0000
switch reg write offset=260device eth2 entered promiscuous mode
4,br0: port 1(eth2) entering learning state
 vbr0: port 1(eth2) entering learning state
alue=ff0000
switch reg write offsetNOTIFY
=eth3: ===> VirtualIF_open
27NOTIFY
04, value=ff0000
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=810000c0
switch reg write offset=2710, value=810000c0
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[SYSTEM]/sbin/brctl addif br0 eth2
[SYSTEM]/sbin/ifconfig eth3 up
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[rc.c::rc_init():489] region valid
RC: wifi_init()
rules = <>, timeout = 20
[SYSTEM]/usr/bin/killall access_logd
killall: access_logd: no process killed
[SYSTEM]/usr/sbin/rc access_log start
[rc debug]/usr/sbin/rc access_log start
ap_name=access_log action=start
[rc.c::rc_action():829] rc_action before add access_log - start
 rc action <access_log @ start> before file_lock.
 rc action <access_log @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_log - start
unlink running file </var/run/rc.access_log.run>
[rc.c::rc_action():829] rc_action before add access_log - start
 rc action <access_log @ start> before file_lock.
 rc action <access_log @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_log - start
unlink running file </var/run/rc.access_log.run>
can't find this application
[rc.c::rc_action():829] rc_action before add access_log - start
 rc action <access_log @ start> before file_lock.
 rc action <access_log @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_log - start
[rc.c::rc_start():732] Calling Start function of access_log
killall: access_logd: no process killed
Access Control log start.
Access Control socket create
unlink running file </var/run/rc.access_log.run>
[SYSTEM]/usr/sbin/rc access_dev start
[rc debug]/usr/sbin/rc access_dev start
ap_name=access_dev action=start
[rc.c::rc_action():829] rc_action before add access_dev - start
 rc action <access_dev @ start> before file_lock.
 rc action <access_dev @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_dev - start
unlink running file </var/run/rc.access_dev.run>
[rc.c::rc_action():829] rc_action before add access_dev - start
 rc action <access_dev @ start> before file_lock.
 rc action <access_dev @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_dev - start
unlink running file </var/run/rc.access_dev.run>
can't find this application
[rc.c::rc_action():829] rc_action before add access_dev - start
 rc action <access_dev @ start> before file_lock.
 rc action <access_dev @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add access_dev - start
[rc.c::rc_start():732] Calling Start function of access_dev
killall: access_devinfo: no process killed
Access Control socket create
unlink running file </var/run/rc.access_dev.run>
[modelinfo_product_id.c::modelinfo_map_index():76] 0xff 0xff, 0xffff.
[modelinfo_product_id.c::modelinfo_map_index():104] default map index to WAC104, flash type is nand
[modelinfo_product_id.c::modelinfo_map_index():109] find index 0 for modelinfo_get_product_name
[modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():182] autoupg_fileinfo_in_nv is wac104_fileinfo.txt
[SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko
ufsd:: trace mask set to 0000000f
ufsd: driver (lke_9.0.0 lke_9.0.0_r237695_b2, LBD=ON, ioctl, bdi, sd2(0), wb, bz, tr) loaded at c0b4f000
NTFS support included
optimized: speed
Build_for__Netgear_R6220_k2.6.36_2014-10-22_lke_9.0.0_r237695_b2

=============rc start
[rc debug]/usr/sbin/rc rwfs start
ap_name=rwfs action=start
[rc.c::rc_action():829] rc_action before add rwfs - start
 rc action <rwfs @ start> before file_lock.
 rc action <rwfs @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add rwfs - start
unlink running file </var/run/rc.rwfs.run>
[rc.c::rc_action():829] rc_action before add rwfs - start
 rc action <rwfs @ start> before file_lock.
 rc action <rwfs @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add rwfs - start
unlink running file </var/run/rc.rwfs.run>
can't find this application
[rc.c::rc_action():829] rc_action before add rwfs - start
 rc action <rwfs @ start> before file_lock.
 rc action <rwfs @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add rwfs - start
unlink running file </var/run/rc.rwfs.run>
can't find this application
[rc debug]/usr/sbin/rc lan start
ap_name=lan action=start
[rc.c::rc_action():829] rc_action before add lan - start

 rc action <lan @ start> before file_lock.
 rc action <lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add lan - start
[rc.c::rc_start():732] Calling Start function of lan
[SYSTEM]/usr/sbin/brctl setfd br0 1
[SYSTEM]/sbin/ifconfig br0 192.168.0.100 netmask 255.255.255.0 broadcast 192.168.0.255
[SYSTEM]/usr/sbin/brctl stp br0 off
[SYSTEM]/usr/sbin/brctl stp br0 on
sh: cannot create /proc/http_file/getLanIp: nonexistent directory
unlink running file </var/run/rc.lan.run>
[rc debug]/usr/sbin/rc wlan start
ap_name=wlan action=start
[rc.c::rc_action():829] rc_action before add wlan - start
 rc action <wlan @ start> before file_lock.
 rc action <wlan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add wlan - start
[rc.c::rc_start():732] Calling Start function of wlan
[wifi_mtk/wifi.c::sync_wireless_nvram():1567] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100
[flash.c::sc_check_remotescfgmgrmagic():795] buf:ff, ff, ff, ff
[flash.c::sc_check_remotescfgmgrmagic():797] magic:31, 3e, c5, 8d
[modelinfo_product_id.c::modelinfo_map_index():76] 0xff 0xff, 0xffff.
[modelinfo_product_id.c::modelinfo_map_index():104] default map index to WAC104, flash type is nand
[modelinfo_product_id.c::modelinfo_map_index():109] find index 0 for modelinfo_get_product_name
[wifi_mtk/wifi.c::start_wireless():1626] SC 5G support level: 11ac
[SYSTEM]mkdir -p /etc/Wireless/RT2860
scfgmgr for local
[SYSTEM]mkdir -p /etc/Wireless/iNIC
region flag in flash:00 00 00 02
[SYSTEM]/bin/mkdir -p /etc/Wireless/RT2860AP/
[SYSTEM]/bin/mkdir -p /etc_ro/Wireless/RT2860AP/
region is PR:0
[SYSTEM]/bin/cp -f /etc_ro/wlan/MT7612E_EEPROM.bin.11ac /etc_ro/wlan/MT7612E_EEPROM.bin
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[wifi_mtk/wifi.c::map_singleskutmp_by_region():1310] all region singlesku.dat exist
[SYSTEM]/bin/rm /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1
rm: cannot remove '/etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620': No such file or directory
[SYSTEM]/bin/rm /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1
rm: cannot remove '/etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E': No such file or directory
[wifi_mtk/wifi.c::map_singleskutmp_by_region():1327] wifi gui region is Europe, 2g CE, 5g CE
[wifi_mtk/wifi.c::map_singleskutmp_by_region():1376] region NOT PR or RU
[SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-2.4.txt /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1
[SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-5G.txt /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1
[SYSTEM]/bin/rm -rf /etc/Wireless/RT2860AP/SingleSKU.dat
[SYSTEM]/bin/mv /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 /etc/Wireless/RT2860AP/SingleSKU.dat
[SYSTEM]/bin/rm -rf /etc_ro/Wireless/iNIC/SingleSKU.dat
[SYSTEM]/bin/mv /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E /etc_ro/Wireless/iNIC/SingleSKU.dat
CHIP: 7603 - current MAC: 14:59:C0:C3:DF:88
Assign MAC: 14:59:C0:C3:DF:88
no update!
CHIP: 7662 - current MAC: 14:59:C0:C3:DF:8C
Assign MAC: 14:59:C0:c3:df:8c
no update!
[SYSTEM]/sbin/iwpriv rai0 set RadioOn=1
Interface doesn't accept private ioctl...
set (8BE2): Network is down
X_BCN DESC a7fd1000 size = 320_setNOTIFY
RX[0] DESC a7fdb000 size = 2048

[SYSTEM]RX[1] DESC a7fdc000 size = 2048
/sbin/ifconfig ra0 up
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
20140814CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
CmdPsRetrieveRsp Disable FW PS Supportstatus:1 !!!!!
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
efuse_probe: efuse = 10000002
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
NVM is FLASH mode
1. Phy Mode = 14
@@@  NICReadEEPROMParameters : pAd->FWLoad=0
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 35
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(13): Not support for HIF_MT yet!
NICInitializeAsic(586): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
mt7603_init_mac_cr()-->
AsicSetMacMaxLen(1574): Set the Max RxPktLen=1024!
<--mt_mac_init()
        WTBL Segment 1 info:
                MemBaseAddr/FID:0x28000/0
                EntrySize/Cnt:32/128
        WTBL Segment 2 info:
                MemBaseAddr/FID:0x40000/0
                EntrySize/Cnt:64/128
        WTBL Segment 3 info:
                MemBaseAddr/FID:0x42000/64
                EntrySize/Cnt:64/128
        WTBL Segment 4 info:
                MemBaseAddr/FID:0x44000/128
                EntrySize/Cnt:32/128
AntCfgInit(2384): Not support for HIF_MT yet!
AsicSendCommandToMcu(3423): Not support for HIF_MT yet!
AsicSendCommandToMcu(3423): Not support for HIF_MT yet!
AsicSendCommandToMcu(3423): Not support for HIF_MT yet!
AsicSendCommandToMcu(3423): Not support for HIF_MT yet!
RTMPSetPhyMode(): channel out of range, use first ch=0
MCS Set = ff ff 00 00 01
AsicSetChBusyStat(889): Not support for HIF_MT yet!
CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 9, central_chl = 9, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 10, central_chl = 10, BW = 0,                                                                   TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 11, central_chl = 11, BW = 0,                                                                   TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 12, central_chl = 12, BW = 0,                                                                   TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#12(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 13, central_chl = 13, BW = 0,                                                                   TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#13(2T2R), BBP_BW=0
CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
SYNC - BBP R4 to 20MHz.l
[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
[PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
[PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
AsicSetRalinkBurstMode(3737): Not support for HIF_MT yet!
RTMPSetPiggyBack(809): Not support for HIF_MT yet!
CmdChannelSwitch: control_chl = 1, central_chl = 3, BW = 1,                                                                     TXStream = 2, RXStream = 2
mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1
AsicSetTxPreamble(3723): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(1738): Not support for HIF_MT yet!
AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
Main bssid = 14:59:c0:c3:df:88
<==== rt28xx_init, Status=0
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
[SYSTEM]/usr/sbin/iwpriv ra0 set IgmpAdd=224.0.0.251
[SYSdevice ra0 entered promiscuous mode
TEbr0: port 2(ra0) entering listening state
M]br0: port 2(ra0) entering listening state
/sbin/brctl addif br0 ra0
[SYSTEM]/bin/led_app on 40
[SYSTEM]/sbNOTIFY
inbuild time =
/i2f0c1o4n0f4i0g80 6r0a6i400 au
prom patch for E3 IC

latform =
SALmP

hw/sw version =
▒▒
patch version =

FW Version:0.0.00 Build:1
Build Time:201411280941____
fw for E3 IC
RX[0] DESC a6f05000 size = 4096
RX[1] DESC a6f06000 size = 4096
E2pAccessMode=2
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 49
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
br0: port 2(ra0) entering learning state
get_chl_grp:illegal channel (173)
get_chl_grp:illegal channel (173)
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=13, low_temp_slope=9
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438
mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438
mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438
br0: topology change detected, propagating
br0: port 1(eth2) entering forwarding state
mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
mt76x2_calibration(channel = 42)
Main bssid = 14:59:c0:c3:df:8c
mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
original vga value(chain0) = 48
original vga value(chain1) = 48
<==== rt28xx_init, Status=0
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
NOTIFY
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
NOTIFY
[SYSTEM]/sbin/brctl addevice rai0 entered promiscuous mode
dibr0: port 3(rai0) entering listening state
f br0: port 3(rai0) entering listening state
br0 rai0
[SYSTEM]/bin/led_app on 40
[libscm_wl.c::GenerateUUID():121]
GUI ASCII string: 38833092-3092-1883-92dd-1459c0c3df88
[libscm_wl.c::GenerateUUID():122]
GUI HEX string: 388330923092188392dd1459c0c3df88
[SYSTEM]/usr/bin/killall miniupnpd_wsc
killall: miniupnpd_wsc: no process killed
[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
+ iwpriv ra0 set WscConfMode=0
+ iwpriv rai0 set WscConfMode=0
+ iwpriv ra0 set WscSetupLock=0
+ iwpriv rai0 set WscSetupLock=0
+ iwpriv ra0 set WscMaxPinAttack=3
+ iwpriv rai0 set WscMaxPinAttack=3
+ route add -host 239.255.255.250 dev br0
+ iwpriv ra0 set WscConfMode=7
+ iwpriv rai0 set WscConfMode=7
+ miniupnpd_wsc -m 1 -I ra0 -P /var/runCan't find DB for id==42
/miniupnpd.ra0 -i eth3 -a 192.168.0.100 -n 7777 -u 38833092-3092-1883-92dd-1459c0c3df88
Unknown option: -I
Unknown option: ra0
Jan  1 00:00:25 miniupnpd[337]: WPS listening on port 7777
[SYSTEM]/bin/cp /pRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fd5e6b0)=60200618!
roRTMPIoctlMAC():after trim space, ptr len=8, pointer(85e27000)=60200618!
c/uptime /tmp/wlan_uptime
[SYSTEM]/RTMPIoctlMAC():wrq->u.data.length=18, pointer(7feb6e70)=60200618=D7E87D10!
binRTMPIoctlMAC():after trim space, ptr len=17, pointer(85e33000)=60200618=D7E87D10!
/led_app on 42
[SYSTEM]/usr/sbin/leRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fdbe100)=60200618!
d_RTMPIoctlMAC():after trim space, ptr len=8, pointer(85e27000)=60200618!
app off 45
[wifi_mtk/wifi.c::need_disable_edcca():1577] wifiregion_in_gui:Europe
[wifi_mtk/wifi.c::start_wireless():1773] ENABLE on EDCCA for 2G and 5G
[SYSTEM]/usr/sbin/iwpriv rai0 mac 1340
rai0      mac:
[0x1340]:04101b3f
[wifi_mtk/wifi.c::start_wireless():1793] org:0x4101b3f. (04101b3f
)[wifi_mtk/wifi.c::start_wireless():1795] now:0x4101b3f
[SYSTEM]/usr/sbin/iwpriv rai0 mac 1340=4101b3f
rai0      mac:
[0x1340]:04101b3f
[SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618
ra0       mac:[0x10618]:d7e87d10
[SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618=D7E87D10
ra0       mac:[0x10618]:d7e87d10
[SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618
ra0       mac:[0x10618]:d7e87d10
unlink running file </var/run/rc.wlan.run>
[rc debug]/usr/sbin/rc printk start
ap_name=printk action=start
[rc.c::rc_action():829] rc_action before add printk - start
 rc action <printk @ start> before file_lock.
 rc action <printk @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add printk - start
[rc.c::rc_start():732] Calling Start function of printk
[SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk
unlink running file </var/run/rc.printk.run>
[rc debug]/usr/sbin/rc timezone start
ap_name=timezone action=start
[rc.c::rc_action():829] rc_action before add timezone - start
 rc action <timezone @ start> before file_lock.
 rc action <timezone @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add timezone - start
[rc.c::rc_start():732] Calling Start function of timezone
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
unlink running file </var/run/rc.timezone.run>
[rc debug]/usr/sbin/rc syslogd start
ap_name=syslogd action=start
[rc.c::rc_action():829] rc_action before add syslogd - start
 rc action <syslogd @ start> before file_lock.
 rc action <syslogd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add syslogd - start
[rc.c::rc_start():732] Calling Start function of syslogd
[SYSTEM]/sbin/syslogd -f /etc/syslog.conf
unlink running file </var/run/rc.syslogd.run>
[rc debug]/usr/sbin/rc httpd start
ap_name=httpd action=start
[rc.c::rc_action():829] rc_action before add httpd - start
 rc action <httpd @ start> before file_lock.
 rc action <httpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add httpd - start
[rc.c::rc_start():732] Calling Start function of httpd
[sc_language.c::create_language_file():426] Create link files for <English>
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP
[sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU>
[sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4>
[SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm
rmmod: ipt_REJECT: No such file or directory
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
[rc.c::rc_stop():771] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
[rc.c::rc_start():732] Calling Start function of firewall
[SYSTEM]/usr/bin/killall -14 access_logd
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():829] rc_action before add syslogd - create
 rc action <syslogd @ create> before file_lock.
 rc action <syslogd @ create lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add syslogd - create
[rc.c::rc_create():813] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
fw_pt
[SYSTEM]/usr/sbin/killall -9 usb_httpd
killall: usb_httpd: no process killed
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300&
unlink running file </var/run/rc.httpd.run>
[rc debug]/usr/sbin/rc remote_httpd start
ap_name=remote_httpd action=start
[rc.c::rc_action():829] rc_action before add remote_httpd - start
 rc action <remote_httpd @ start> before file_lock.
 rc action <remote_httpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add remote_httpd - start
[rc.c::rc_start():732] Calling Start function of remote_httpd
unlink running file </var/run/rc.remote_httpd.run>
[rc debug]/usr/sbin/rc dhcpd start
ap_name=dhcpd action=start
[rc.c::rc_action():829] rc_action before add dhcpd - start
 rc action <dhcpd @ start> before file_lock.
 rc action <dhcpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dhcpd - start
[rc.c::rc_start():732] Calling Start function of dhcpd
killall: udhcpd: no process killed
unlink running file </var/run/rc.dhcpd.run>
[rc debug]/usr/sbin/rc ntp start
ap_name=ntp action=start
[rc.c::rc_action():829] rc_action before add ntp - start
 rc action <ntp @ start> before file_lock.
 rc action <ntp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ntp - start
[rc.c::rc_start():732] Calling Start function of ntp
[SYSTEM]/usr/sbin/netgear_ntp -z GMT+0&
unlink running file </var/run/rc.ntp.run>
[rc debug]/usr/sbin/rc route start
ap_name=route action=start
[rc.c::rc_action():829] rc_action before add route - start
 rc action <route @ start> before file_lock.
 rc action <route @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - start
[rc.c::rc_start():732] Calling Start function of route
unlink running file </var/run/rc.route.run>
[rc debug]/usr/sbin/rc ripd start
ap_name=ripd action=start
[rc.c::rc_action():829] rc_action before add ripd - start
 rc action <ripd @ start> before file_lock.
 rc action <ripd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ripd - start
[rc.c::rc_start():732] Calling Start function of ripd
unlink running file </var/run/rc.ripd.run>
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():829] rc_action before add dnrd - start
 rc action <dnrd @ start> before file_lock.
 rc action <dnrd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - start
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
unlink running file </var/run/rc.dnrd.run>
[rc debug]/usr/sbin/rc potcounter start
ap_name=potcounter action=start
[rc.c::rc_action():829] rc_action before add potcounter - start
 rc action <potcounter @ start> before file_lock.
 rc action <potcounter @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.potcounter.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add potcounter - start
[rc.c::rc_start():732] Calling Start function of potcounter
unlink running file </var/run/rc.potcounter.run>
[rc debug]/usr/sbin/rc lltd start
ap_name=lltd action=start
[rc.c::rc_action():829] rc_action before add lltd - start
 rc action <lltd @ start> before file_lock.
 rc action <lltd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add lltd - start
[rc.c::rc_start():732] Calling Start function of lltd
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
unlink running file </var/run/rc.lltd.run>
[rc debug]/usr/sbin/rc usb_init start
ap_name=usb_init action=start
[rc.c::rc_action():829] rc_action before add usb_init - start
 rc action <usb_init @ start> before file_lock.
 rc action <usb_init @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_init.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_init - start
[rc.c::rc_start():732] Calling Start function of usb_init
[SYSTEM]/etc/mtk/mt7621_smp.sh wifi
[SYSTEM]/bin/rm /etc/samba/secrets.tdb
rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
[SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
[SYSTEM]/etc/mtk/mt7621_smp.sh wifi
[SYSTEM]/bin/rm /etc/samba/secrets.tdb
rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
[SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
unlink running file </var/run/rc.usb_init.run>
[rc debug]/usr/sbin/rc debug_mode start
ap_name=debug_mode action=start
[rc.c::rc_action():829] rc_action before add debug_mode - start
 rc action <debug_mode @ start> before file_lock.
 rc action <debug_mode @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add debug_mode - start
[rc.c::rc_start():732] Calling Start function of debug_mode
unlink running file </var/run/rc.debug_mode.run>
[rc debug]/usr/sbin/rc wifi_isolation start
ap_name=wifi_isolation action=start
[rc.c::rc_action():829] rc_action before add wifi_isolation - start
 rc action <wifi_isolation @ start> before file_lock.
 rc action <wifi_isolation @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add wifi_isolation - start
[rc.c::rc_start():732] Calling Start function of wifi_isolation
[wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation!
unlink running file </var/run/rc.wifi_isolation.run>
[rc debug]/usr/sbin/rc mediaserver start
ap_name=mediaserver action=start
[rc.c::rc_action():829] rc_action before add mediaserver - start
 rc action <mediaserver @ start> before file_lock.
 rc action <mediaserver @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.mediaserver.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add mediaserver - start
[rc.c::rc_start():732] Calling Start function of mediaserver
#### media server is disable
unlink running file </var/run/rc.mediaserver.run>
[rc debug]/usr/sbin/rc bridge_iptv_port start
ap_name=bridge_iptv_port action=start
[rc.c::rc_action():829] rc_action before add bridge_iptv_port - start
 rc action <bridge_iptv_port @ start> before file_lock.
 rc action <bridge_iptv_port @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add bridge_iptv_port - start
unlink running file </var/run/rc.bridge_iptv_port.run>
[rc.c::rc_action():829] rc_action before add bridge_iptv_port - start
 rc action <bridge_iptv_port @ start> before file_lock.
 rc action <bridge_iptv_port @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add bridge_iptv_port - start
unlink running file </var/run/rc.bridge_iptv_port.run>
can't find this application
[rc.c::rc_action():829] rc_action before add bridge_iptv_port - start
 rc action <bridge_iptv_port @ start> before file_lock.
 rc action <bridge_iptv_port @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add bridge_iptv_port - start
unlink running file </var/run/rc.bridge_iptv_port.run>
can't find this application
[rc debug]/usr/sbin/rc vlan start
ap_name=vlan action=start
[rc.c::rc_action():829] rc_action before add vlan - start
 rc action <vlan @ start> before file_lock.
 rc action <vlan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add vlan - start
[rc.c::rc_start():732] Calling Start function of vlan
[SYSTEM]/sbin/chmod +x /var/vlan_up.sh
[SYSTEM]/bin/sh -x /var/vlan_up.sh
[SYSTEM]/sbin/chmod +x /var/vlan_down.sh
unlink running file </var/run/rc.vlan.run>
[rc debug]/usr/sbin/rc dbus start
ap_name=dbus action=start
[rc.c::rc_action():829] rc_action before add dbus - start
 rc action <dbus @ start> before file_lock.
 rc action <dbus @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dbus - start
unlink running file </var/run/rc.dbus.run>
[rc.c::rc_action():829] rc_action before add dbus - start
 rc action <dbus @ start> before file_lock.
 rc action <dbus @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dbus - start
unlink running file </var/run/rc.dbus.run>
can't find this application
[rc.c::rc_action():829] rc_action before add dbus - start
 rc action <dbus @ start> before file_lock.
 rc action <dbus @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dbus - start
unlink running file </var/run/rc.dbus.run>
can't find this application
=============rc finish
run smp wifi
run smp wifi done
  PID USER       VSZ STAT COMMAND
    1 root      1516 S    init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW   [kworker/u:0]
    6 root         0 SW   [migration/0]
    7 root         0 SW   [migration/1]
    8 root         0 SW   [kworker/1:0]
    9 root         0 SW   [ksoftirqd/1]
   10 root         0 SW<  [khelper]
   11 root         0 SW   [kworker/1:1]
   12 root         0 SW   [sync_supers]
   13 root         0 SW   [bdi-default]
   14 root         0 SW<  [kblockd]
   15 root         0 SW   [khubd]
   16 root         0 SW   [kswapd0]
   17 root         0 SW   [fsnotify_mark]
   18 root         0 SW<  [xfs_mru_cache]
   19 root         0 SW<  [xfslogd]
   20 root         0 SW<  [xfsdatad]
   21 root         0 SW<  [xfsconvertd]
   22 root         0 SW<  [crypto]
   31 root         0 SW   [mtdblock0]
   32 root         0 SW   [mtdblock1]
   33 root         0 SW   [mtdblock2]
   34 root         0 SW   [mtdblock3]
   35 root         0 SW   [mtdblock4]
   36 root         0 SW   [mtdblock5]
   37 root         0 SW   [mtdblock6]
   38 root         0 SW   [mtdblock7]
   39 root         0 SW   [mtdblock8]
   40 root         0 SW   [mtdblock9]
   41 root         0 SW   [mtdblock10]
   42 root         0 SW   [mtdblock11]
   43 root         0 SW   [mtdblock12]
   44 root         0 SW   [mtdblock13]
   45 root         0 SW   [mtdblock14]
   46 root         0 SW   [mtdblock15]
   47 root         0 SW   [mtdblock16]
   48 root         0 SW   [mtdblock17]
   49 root         0 SW   [mtdblock18]
   50 root         0 SW   [mtdblock19]
   51 root         0 SW   [mtdblock20]
   52 root         0 SW   [mtdblock21]
   53 root         0 SW   [kworker/u:1]
   60 root         0 SW   [kworker/0:1]
   62 root      1520 S    /bin/sh /usr/etc/rcS
  150 root      1032 S    /sbin/klogd
  152 root       920 S    /usr/sbin/cmd_agent_ap
  222 root      1028 S    /sbin/access_logd
  235 root      1140 S    /sbin/access_devinfo
  268 root      1216 S    /usr/sbin/scfgmgr
  303 root         0 SW   [RtmpCmdQTask]
  304 root         0 SW   [RtmpWscTask]
  305 root         0 SW   [RtmpMlmeTask]
  314 root         0 SW   [RtmpCmdQTask]
  315 root         0 SW   [RtmpWscTask]
  316 root         0 SW   [RtmpMlmeTask]
  337 root      1084 S    miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -
  379 root      1092 S    /sbin/syslogd -f /etc/syslog.conf
  891 root       940 S    /usr/sbin/netgear_ntp -z GMT+0
 1324 root      3056 S    /usr/sbin/mini_httpd -d /www -r NETGEAR WAC104 -c **.
 1326 root      1104 S    /usr/sbin/potcounter
 1332 root      1428 S    dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8
 1334 root      1144 S    /usr/bin/lld2 br0
 1448 root      1516 R    /bin/ps
[rc debug]/usr/sbin/rc upnp start
ap_name=upnp action=start
[rc.c::rc_action():829] rc_action before add upnp - start
 rc action <upnp @ start> before file_lock.
 rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
[rc.c::rc_action():829] rc_action before add upnp - start
 rc action <upnp @ start> before file_lock.
 rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
can't find this application
[rc.c::rc_action():829] rc_action before add upnp - start
 rc action <upnp @ start> before file_lock.
 rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add upnp - start
[rc.c::rc_start():732] Calling Start function of upnp
[upnp/upnp_cfg.c::start_upnp():68] AP Mode no need upnp
unlink running file </var/run/rc.upnp.run>
[rc debug]/usr/sbin/rc schedule restart
[rc.c::rc_action():829] rc_action before add schedule - restart
 rc action <schedule @ restart> before file_lock.
 rc action <schedule @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add schedule - restart
unlink running file </var/run/rc.schedule.run>
[rc.c::rc_action():829] rc_action before add schedule - restart
 rc action <schedule @ restart> before file_lock.
 rc action <schedule @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add schedule - restart
[rc.c::rc_start():732] Calling Start function of schedule
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
/usr/etc/rcS: line 294: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
/usr/etc/rcS: line 295: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
/usr/etc/rcS: line 299: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
unlink running file </var/run/rc.schedule.run>
failover NOT enable, run rc wan to start wan
[rc debug]/usr/sbin/rc reset_lan start
ap_name=reset_lan action=start
[rc debug][rc.c::rc_action():829] rc_action before add reset_lan - start
/usr/sbin/rc wan  rc action <reset_lan @ start> before file_lock.
start
 rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
[wan/wan.c::start_wan():1219] IPV6IPV4PPP_ONE_SESSION not enable
[SYSTEM]/usr/sbin/brctl delif br0 eth3
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
[rc.c::rc_action():829] rc_action before add reset_lan - start
 rc action <reset_lan @ start> before file_lock.
 rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
can't find this application
[rc.c::rc_action():829] rc_action before add reset_lan - start
 rc action <reset_lan @ start> before file_lock.
 rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
device eth3 is not a slave of br0
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add reset_lan - start
[rc.c::rc_start():732] Calling Start function of reset_lan
[SYSTEM]/usr/bin/killall netgear_ntp
down port 0
Set: phy[0].reg[0] = 1840
down port 1
killall: netgear_ntp: no process killed
Set: phy[1].reg[0] = 1840
killall: miniupnpd: no process killed
[SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
down port 2
killall: miniupnpd: no process killed
Set: phy[2].reg[0] = 1840
killall: ripd: no process killed
down port 3
killall: zebra: no process killed
Set: phy[3].reg[0] = 1840
killall: ripd: no process killed
killall: zebra: no process killed
[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
[SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE
[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP
sh: syntax error: "(" unexpected
[SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
[SYSTEM]/usr/bin/killall pppd
killall: pppd: no process killed
[SYSTEM]/usr/bin/killall openl2tpd
killall: openl2tpd: no process killed
[SYSTEM]/usr/bin/killall udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/bin/killall pppoe-relay
killall: pppoe-relay: no process killed
[SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1
[SYSTEM]/sbin/ifconfig eth3 down
[SYSTEM]/sbin/ifconfig eth3 hw ether 14:59:C0:c3:df:89
[SYSTEM]/sbin/ifconfig eth3 up
[SYSTEM]/sbin/ifconfig eth3 mtu 1500
[wan/wan.c::start_wan():1429] wan_mode is <bridge>
[SYSTEM]/bin/rmmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
rmmod: /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko: No such file or directory
[SYSTEM]/usr/sbin/brctl addif br0 eth3
[SYSTEM]ifconfig br0 0.0.0.0
[SYSTEM]ifconfig br0 up
[SYSTEM]/usr/sbin/rc route stop
[rc debug]/usr/sbin/rc route stop
ap_name=route action=stop
[rc.c::rc_action():829] rc_action before add route - stop
 rc action <route @ stop> before file_lock.
 rc action <route @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - stop
[rc.c::rc_stop():771] Calling Stop function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/usr/sbin/rc dhcpd stop
[rc debug]/usr/sbin/rc dhcpd stop
ap_name=dhcpd action=stop
[rc.c::rc_action():829] rc_action before add dhcpd - stop
 rc action <dhcpd @ stop> before file_lock.
 rc action <dhcpd @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dhcpd - stop
[rc.c::rc_stop():771] Calling Stop function of dhcpd
killall: udhcpd: no process killed
unlink running file </var/run/rc.dhcpd.run>
[SYSTEM]/usr/sbin/rc igmp stop
[rc debug]/usr/sbin/rc igmp stop
ap_name=igmp action=stop
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
can't find this application
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
[rc.c::rc_stop():771] Calling Stop function of igmp
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
killall: igmpproxy: no process killed
[SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
unlink running file </var/run/rc.igmp.run>
[SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko
[SYSTEM]/usr/sbin/killall -9 udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script &
[dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started
[clientpacket.c::send_discover():175] Sending discover...
up port 0
Set: phy[0].reg[0] = 1240
up port 1
Set: phy[1].reg[0] = 1240
up port 2
Set: phy[2].reg[0] = 1240
up port 3
Set: phy[3].reg[0] = 1240
unlink running file </var/run/rc.reset_lan.run>
preapre_sys_for_3g
mknod: /dev/zero: File exists
mknod: /dev/ttyUSB0: File exists
mknod: /dev/ttyUSB1: File exists
mknod: /dev/ttyUSB2: File exists
mknod: /dev/ttyUSB3: File exists
mkdir: cannot create directory '/var': File exists
preapre_sys_for_3g done
failover NOT enable
[clientpacket.c::send_discover():175] Sending discover...
[clientpacket.c::send_discover():175] Sending discover...
cable_down_once
[rc debug]/usr/sbin/rc down_manage stop
ap_name=down_manage action=stop
[rc.c::rc_action():829] rc_action before add down_manage - stop
 rc action <down_manage @ stop> before file_lock.
 rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
[rc.c::rc_action():829] rc_action before add down_manage - stop
 rc action <down_manage @ stop> before file_lock.
 rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
[rc debug]/usr/sbin/rc lan ap_down
ap_name=lan action=ap_down
[rc.c::rc_action():829] rc_action before add lan - ap_down
 rc action <lan @ ap_down> before file_lock.
 rc action <lan @ ap_down lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
can't find this application
[rc.c::rc_action():829] rc_action before add down_manage - stop
 rc action <down_manage @ stop> before file_lock.
 rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add lan - ap_down
[SYSTEM]/usr/sbin/ip route del to default 2>/dev/null
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
can't find this application
[rc debug]/usr/sbin/rc usb_printer start
ap_name=usb_printer action=start
[rc.c::rc_action():829] rc_action before add usb_printer - start
 rc action <usb_printer @ start> before file_lock.
 rc action <usb_printer @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_printer - start
unlink running file </var/run/rc.usb_printer.run>
[rc.c::rc_action():829] rc_action before add usb_printer - start
 rc action <usb_printer @ start> before file_lock.
 rc action <usb_printer @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_printer - start
unlink running file </var/run/rc.usb_printer.run>
can't find this application
[rc.c::rc_action():829] rc_action before add usb_printer - start
 rc action <usb_printer @ start> before file_lock.
 rc action <usb_printer @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_printer - start
[rc.c::rc_start():732] Calling Start function of usb_printer
[SYSTEM]/sbin/killall KC_BONJOUR
killall: KC_BONJOUR: no process killed
[SYSTEM]/usr/sbin/rc dnrd stop
[SYSTEM]/sbin/killall KC_PRINT
[rc debug]/usr/sbin/rc dnrd stop
ap_name=dnrd action=stop
[rc.c::rc_action():829] rc_action before add dnrd - stop
 rc action <dnrd @ stop> before file_lock.
 rc action <dnrd @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - stop
[rc.c::rc_stop():771] Calling Stop function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
killall: KC_PRINT: no process killed
[SYSTEM]/sbin/rmmod usblp
rmmod: usblp: No such file or directory
[SYSTEM]/sbin/rmmod NetUSB.ko
rmmod: NetUSB.ko: No such file or directory
[SYSTEM]/sbin/rmmod GPL_NetUSB.ko
iptables: No chain/target/match by that name.
rmmod: GPL_NetUSB.ko: No such file or directory
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
unlink running file </var/run/rc.usb_printer.run>
  PID USER       VSZ STAT COMMAND
    1 root      1516 S    init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW   [kworker/u:0]
    6 root         0 SW   [migration/0]
    7 root         0 SW   [migration/1]
    8 root         0 SW   [kworker/1:0]
    9 root         0 SW   [ksoftirqd/1]
   10 root         0 SW<  [khelper]
   11 root         0 SW   [kworker/1:1]
   12 root         0 SW   [sync_supers]
   13 root         0 SW   [bdi-default]
   14 root         0 SW<  [kblockd]
   15 root         0 SW   [khubd]
   16 root         0 SW   [kswapd0]
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
   17 root         0 SW   [fsnotify_mark]
   18 root         0 SW<  [xfs_mru_cache]
   19 root         0 SW<  [xfslogd]
   20 root         0 SW<  [xfsdatad]
   21 root         0 SW<  [xfsconvertd]
   22 root         0 SW<  [crypto]
   31 root         0 SW   [mtdblock0]
   32 root         0 SW   [mtdblock1]
   33 root         0 SW   [mtdblock2]
   34 root         0 SW   [mtdblock3]
   35 root         0 SW   [mtdblock4]
   36 root         0 SW   [mtdblock5]
   37 root         0 SW   [mtdblock6]
   38 root         0 SW   [mtdblock7]
   39 root         0 SW   [mtdblock8]
   40 root         0 SW   [mtdblock9]
   41 root         0 SW   [mtdblock10]
   42 root         0 SW   [mtdblock11]
   43 root         0 SW   [mtdblock12]
   44 root         0 SW   [mtdblock13]
   45 root         0 SW   [mtdblock14]
   46 root         0 SW   [mtdblock15]
   47 root         0 SW   [mtdblock16]
   48 root         0 SW   [mtdblock17]
   49 root         0 SW   [mtdblock18]
   50 root         0 SW   [mtdblock19]
   51 root         0 SW   [mtdblock20]
   52 root         0 SW   [mtdblock21]
   53 root         0 SW   [kworker/u:1]
   60 root         0 SW   [kworker/0:1]
   62 root      1520 S    /bin/sh /usr/etc/rcS
  150 root      1032 S    /sbin/klogd
  152 root       920 S    /usr/sbin/cmd_agent_ap
  222 root      1028 S    /sbin/access_logd
  235 root      1140 S    /sbin/access_devinfo
  268 root      1216 S    /usr/sbin/scfgmgr
  303 root         0 SW   [RtmpCmdQTask]
  304 root         0 SW   [RtmpWscTask]
  305 root         0 SW   [RtmpMlmeTask]
  314 root         0 SW   [RtmpCmdQTask]
  315 root         0 SW   [RtmpWscTask]
  316 root         0 SW   [RtmpMlmeTask]
  337 root      1084 S    miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -
  379 root      1092 S    /sbin/syslogd -f /etc/syslog.conf
 1324 root      3056 S    /usr/sbin/mini_httpd -d /www -r NETGEAR WAC104 -c **.
 1326 root      1104 S    /usr/sbin/potcounter
 1332 root      1428 S    dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8
 1334 root      1144 S    /usr/bin/lld2 br0
 1457 root       948 S    /usr/sbin/crond
 1458 root      1404 S    /usr/sbin/multi_pb_app 90 91 92 10 50
 1460 root         0 Z    [crond]
 1461 root         0 Z    [crond]
 1510 root      2136 S    /usr/sbin/rc wan start
 1512 root       924 S    /usr/sbin/cmd_agent
 2096 root      1108 S    /usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script
 2247 root      1104 S    usr/sbin/wan_monitor
 2248 root      1296 S    usr/sbin/ap_monitor
 2270 root      1512 S    sh -c /usr/sbin/rc lan ap_down
 2272 root      2116 S    /usr/sbin/rc lan ap_down
 2282 root       936 S    /usr/sbin/watchdog
 2298 root      1512 S    sh -c /usr/sbin/rc dnrd stop
 2301 root      2124 S    /usr/sbin/rc dnrd stop
 2415 root      1516 R    /bin/ps
 2521 root      1512 S    sh -c iptables -t nat -D PREROUTING -i br0 -p udp --d
 2522 root      1760 R    iptables -t nat -D PREROUTING -i br0 -p udp --dport 5
/usr/etc/rcS: line 376: /usr/sbin/led_test: not found
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[rc debug]/usr/sbin/rc check_kwilt start
ap_name=check_kwilt action=start
[rc.c::rc_action():829] rc_action before add check_kwilt - start
 rc action <check_kwilt @ start> before file_lock.
 rc action <check_kwilt @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run
/usr/etc/rcS: line 379: /usr/sbin/kwilt_daemon: not found
starting pid 2633, tty '/dev/ttyS1': '/bin/sh'
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add check_kwilt - start
unlink running file </var/run/rc.check_kwilt.run>
[rc.c::rc_action():829] rc_action before add check_kwilt - start
 rc action <check_kwilt @ start> before file_lock.
 rc action <check_kwilt @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run
# unlink running file </var/run/rc.dnrd.run>
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add check_kwilt - start
unlink running file </var/run/rc.check_kwilt.run>
can't find this application
[rc.c::rc_action():829] rc_action before add check_kwilt - start
 rc action <check_kwilt @ start> before file_lock.
 rc action <check_kwilt @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add check_kwilt - start
unlink running file </var/run/rc.check_kwilt.run>
can't find this application
[SYSTEM]/usr/sbin/rc wan restart
[rc debug]/usr/sbin/rc wan restart
[SYSTEM]/usr/bin/killall netgear_ntp
killall: netgear_ntp: no process killed
killall: miniupnpd: no process killed
[SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
killall: miniupnpd: no process killed
killall: ripd: no process killed
killall: zebra: no process killed
[basic/lan_cfg.c::start_lan_ap():329] udhcpc cannot get IP, run autoip app to generate IP for br0
[SYSTEM]/usr/sbin/killall -SIGUSR2 udhcpc
[dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=17
[SYSTEM]/usr/sbin/autoip
We will test autoip: 192.168.0.100
send 0 request pkgs
killall: ripd: no process killed
killall: zebra: no process killed
[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
[SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE
[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP
sh: syntax error: "(" unexpected
[SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
[SYSTEM]/usr/bin/killall pppd
killall: pppd: no process killed
[SYSTEM]/usr/bin/killall openl2tpd
send 1 request pkgs
killall: openl2tpd: no process killed
[SYSTEM]/usr/bin/killall udhcpc
[dhcpc.c::release_requested():161] Received SIGUSR2, state=7,sig=0
[dhcpc.c::terminate():206] Received SIGTERM
[SYSTEM]/usr/bin/killall pppoe-relay
killall: pppoe-relay: no process killed
[SYSTEM]/sdevice eth3 left promiscuous mode
bibr0: port 4(eth3) entering forwarding state
n/ifconfig eth3 0.0.0.0 >/dev/null 2>&1
[wan/wan.c::start_wan():1219] IPV6IPV4PPP_ONE_SESSION not enable
[SYSTEM]/usr/sbin/brctl delif br0 eth3
[SYSTEM]/usr/bin/killall netgear_ntp
killall: netgear_ntp: no process killed
killall: miniupnpd: no process killed
[SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
killall: miniupnpd: no process killed
killall: ripd: no process killed
killall: zebra: no process killed
send 2 request pkgs
We will do announce for autoip: 192.168.0.100
send 0 request pkgs
killall: ripd: no process killed
killall: zebra: no process killed
[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
[SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE
[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP
sh: syntax error: "(" unexpected
[SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
[SYSTEM]/usr/bin/killall pppd
killall: pppd: no process killed
[SYSTEM]/usr/bin/killall openl2tpd
killall: openl2tpd: no process killed
[SYSTEM]/usr/bin/killall udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/bin/killall pppoe-relay
killall: pppoe-relay: no process killed
[SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1
[SYSTEM]/sbin/ifconfigNOTIFY
 eth3 down
eth3: ===> VirtualIF_close
NOTIFY
[SYSTEM]/sbin/ifconfigGDMA2_MAC_ADRH -- : 0x00001459
 eGDMA2_MAC_ADRL -- : 0xc0c3df89
th3NOTIFY
 hw ether 14:59:C0:c3:df:89
NOTIFY
[eth3: ===> VirtualIF_open
SYSNOTIFY
TEM]/sbin/ifconfig eth3 up
[SYSTEM]/sbin/ifconfig eth3 mtu 1500
[wan/wan.c::start_wan():1429] wan_mode is <bridge>
[SYdevice eth3 entered promiscuous mode
STEbr0: port 4(eth3) entering listening state
M]br0: port 4(eth3) entering listening state
/bin/rmmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
rmmod: /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko: No such file or directory
[SYSTEM]/usr/sbin/brctl addif br0 eth3
[SYSTEM]ifconfig br0 0.0.0.0
[SYSTEM]ifconfig br0 up
[SYSTEM]/usr/sbin/rc route stop
[rc debug]/usr/sbin/rc route stop
ap_name=route action=stop
[rc.c::rc_action():829] rc_action before add route - stop
 rc action <route @ stop> before file_lock.
 rc action <route @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - stop
[rc.c::rc_stop():771] Calling Stop function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/usr/sbin/rc dhcpd stop
[rc debug]/usr/sbin/rc dhcpd stop
ap_name=dhcpd action=stop
[rc.c::rc_action():829] rc_action before add dhcpd - stop
 rc action <dhcpd @ stop> before file_lock.
 rc action <dhcpd @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dhcpd - stop
[rc.c::rc_stop():771] Calling Stop function of dhcpd
killall: udhcpd: no process killed
unlink running file </var/run/rc.dhcpd.run>
[SYSTEM]/usr/sbin/rc igmp stop
[rc debug]/usr/sbin/rc igmp stop
ap_name=igmp action=stop
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
can't find this application
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
[rc.c::rc_stop():771] Calling Stop function of igmp
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
killall: igmpproxy: no process killed
[SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
unlink running file </var/run/rc.igmp.run>
[SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko
insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists
[SYSTEM]/usr/sbin/killall -9 udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script &
[dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started
[clientpacket.c::send_discover():175] Sending discover...
br0: port 4(eth3) entering learning state
send 1 request pkgs
br0: topology change detected, propagating
br0: port 4(eth3) entering forwarding state
[clientpacket.c::send_discover():175] Sending discover...
probe success with latest probe IP
[clientpacket.c::send_discover():175] Sending discover...
[SYSTEM]/usr/sbin/killall -SIGUSR1 udhcpc
[dhcpc.c::renew_requested():139] Received SIGUSR1 or sig 50, state=0
[clientpacket.c::send_discover():175] Sending discover...
[basic/lan_cfg.c::start_lan_ap():338] autoip generate a IP for br0, use it and run lan ap up
[rc debug]/usr/sbin/rc dnrd restart
ap_name=dnrd action=restart
[rc.c::rc_action():829] rc_action before add dnrd - restart
 rc action <dnrd @ restart> before file_lock.
 rc action <dnrd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - restart
[rc.c::rc_stop():771] Calling Stop function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
unlink running file </var/run/rc.dnrd.run>
[rc debug]/usr/sbin/rc httpd restart
ap_name=httpd action=restart
[rc.c::rc_action():829] rc_action before add httpd - restart
 rc action <httpd @ restart> before file_lock.
 rc action <httpd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add httpd - restart
[rc.c::rc_stop():771] Calling Stop function of httpd
killall: remote_httpd: no process killed
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
[rc.c::rc_start():732] Calling Start function of httpd
[sc_language.c::create_language_file():426] Create link files for <English>
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP
[sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU>
[sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4>
ln: /tmp/www/www.eng: Read-only file system
[SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firblock items:
ewall @ restart> beinput:clear

fore file_lock.
 rc action <ficlamp total entry used:0
rewall @ restart lock = 3> after file_loctotal count:0
k.
input str:clear

[Spsd clear oldest entry
YSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.runroc_write_echo_chargen receive: len: 6, input: clear
 proc_write_echo_chargen receive: clear list

 Leaving proc_write_echo_chargen : size: 6
 rc action < unlock = 3> after fwan interface=[eth3], index=9
ibr interface=[br0], index=8
le_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
[rc.c::rc_stop():771] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
[rc.c::rc_start():732] Calling Start function of firewall
[SYSTEM]/usr/bin/killall -14 access_logd
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():829] rc_action before add syslogd - create
 rc action <syslogd @ create> before file_lock.
 rc action <syslogd @ create lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add syslogd - create
[rc.c::rc_create():813] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
fw_pt
[SYSTEM]/usr/sbin/killall -9 usb_httpd
killall: usb_httpd: no process killed
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[clientpacket.c::send_discover():175] Sending discover...
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300&
unlink running file </var/run/rc.httpd.run>
[SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null
[SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null
[clientpacket.c::send_discover():175] Sending discover...
username=admin,passwd=password
[basic/lan_cfg.c::start_lan_ap():322] udhcpc get IP
[SYSTEM]/usr/sbin/rc dnrd start
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():829] rc_action before add dnrd - start
 rc action <dnrd @ start> before file_lock.
 rc action <dnrd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - start
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
unlink running file </var/run/rc.dnrd.run>
[SYSTEM]/usr/sbin/rc route start
[rc debug]/usr/sbin/rc route start
ap_name=route action=start
[rc.c::rc_action():829] rc_action before add route - start
 rc action <route @ start> before file_lock.
 rc action <route @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
startsmbfilepwent_internal: file /etc/samba/smbpasswd did not exist. File successfully created.
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - start
[rc.c::rc_start():732] Calling Start function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/bin/killall failover
killall: failover: no process killed
[wan/wan.c::start_wan():1513] ipv6 restart, v4 mode bridge v6 mode disable
[SYSTEM]/usr/sbin/rc ipv6 restart
[rc debug]/usr/sbin/rc ipv6 restart
ap_name=ipv6 action=restart
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ipv6 - restart
unlink running file </var/run/rc.ipv6.run>
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ipv6 - restart
unlink running file </var/run/rc.ipv6.run>
can't find this application
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ipv6 - restart
[rc.c::rc_stop():771] Calling Stop function of ipv6
[ipv6/ipv6.c::stop_ipv6():30] AP Mode no need ipv6.
[rc.c::rc_start():732] Calling Start function of ipv6
[ipv6/ipv6.c::start_ipv6():102] AP Mode no need ipv6.
unlink running file </var/run/rc.ipv6.run>
[SYSTEM]/usr/sbin/rc qos stop
[rc debug]/usr/sbin/rc qos stop
ap_name=qos action=stop
[rc.c::rc_action():829] rc_action before add qos - stop
 rc action <qos @ stop> before file_lock.
 rc action <qos @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.qos.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add qos - stop
unlink running file </var/run/rc.qos.run>
[rc.c::rc_action():829] rc_action before add qos - stop
 rc action <qos @ stop> before file_lock.
 rc action <qos @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.qos.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add qos - stop
[rc.c::rc_stop():771] Calling Stop function of qos
[SYSTEM]/usr/sbin/tc qdisc del dev eth3 root 2> /dev/null
Added user admin.
----------------
[SYSTEM]echo "0," > /proc/qos
[SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19
sh: cannot create /proc/qos: nonexistent directory
[SYSTEM]echo 0 > /proc/sys/net/netfilter/nf_conntrack_acct
[SYSTEM]/sbin/rmmod /lib/modules/sc_priority.ko
[rc debug]/usr/sbin/rc lan restart
ap_name=lan action=restart
[rc.c::rc_action():829] rc_action before add lan - restart
 rc action <lan @ restart> before file_lock.
 rc action <lan @ restart lock = 3> after file_lock.
 rc action <lan@41> exit without remove running flag file.
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add lan - restart
[rc.c::rc_stop():771] Calling Stop function of lan
rmmod: /lib/modules/sc_priority.ko: No such file or directory
[rc.c::rc_start():732] Calling Start function of lan
[SYSTEM]/usr/sbin/brctl setfd br0 1
[SYSTEM]/usr/sbin/tc qdisc del dev br0 root 2> /dev/null
[SYSTEM]ifconfig br0 0.0.0.0
[SYSTEM]/usr/sbin/iptables -t mangle -F POSTROUTING
[SYSTEM]ifconfig br0 up
[SYSTEM]/usr/sbin/rc route stop
[rc debug]/usr/sbin/rc route stop
ap_name=route action=stop
[rc.c::rc_action():829] rc_action before add route - stop
 rc action <route @ stop> before file_lock.
 rc action <route @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - stop
[rc.c::rc_stop():771] Calling Stop function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/usr/sbin/rc dhcpd stop
[SYSTEM]/usr/sbin/iptables -t mangle -F TURBO_VIDEO
[rc debug]/usr/sbin/rc dhcpd stop
ap_name=dhcpd action=stop
[rc.c::rc_action():829] rc_action before add dhcpd - stop
 rc action <dhcpd @ stop> before file_lock.
 rc action <dhcpd @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dhcpd - stop
[rc.c::rc_stop():771] Calling Stop function of dhcpd
killall: udhcpd: no process killed
iptables: No chain/target/match by that name.
unlink running file </var/run/rc.dhcpd.run>
[SYSTEM]/usr/sbin/iptables -t mangle -X TURBO_VIDEO
[SYSTEM]/usr/sbin/rc igmp stop
[rc debug]/usr/sbin/rc igmp stop
ap_name=igmp action=stop
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
iptables: [SYSTEM]/usr/sbin/rc usb_service restart
No chain/target/match by that name.
unlink running file </var/run/rc.qos.run>
[SYSTEM]/usr/sbin/rc httpd restart
[rc debug]/usr/sbin/rc usb_service restart
ap_name=usb_service action=restart
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
 rc action <usb_service @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
unlink running file </var/run/rc.igmp.run>
can't find this application
[rc.c::rc_action():829] rc_action before add igmp - stop
 rc action <igmp @ stop> before file_lock.
 rc action <igmp @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run
[rc debug]/usr/sbin/rc httpd restart
ap_name=httpd action=restart
[rc.c::rc_action():829] rc_action before add httpd - restart
 rc action <httpd @ restart> before file_lock.
 rc action <httpd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
unlink running file </var/run/rc.usb_service.run>
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action <usb_service @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add httpd - restart
[rc.c::rc_stop():771] Calling Stop function of httpd
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add igmp - stop
[rc.c::rc_stop():771] Calling Stop function of igmp
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
unlink running file </var/run/rc.usb_service.run>
can't find this application
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action <usb_service @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
[rc.c::rc_stop():771] Calling Stop function of usb_service
[SYSTEM]/etc/mtk/mt7621_smp.sh wifi
killall: remote_httpd: no process killed
[rc.c::rc_start():732] Calling Start function of httpd
[sc_language.c::create_language_file():426] Create link files for <English>
iptables: Bad rule (does a matching rule exist in that chain?).
[SYSTEM]/bin/rm /etc/samba/secrets.tdb
iptables: Bad rule (does a matching rule exist in that chain?).
rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
[SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
killall: igmpproxy: no process killed
[SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327
sh: cannot create /proc/sw_ar8327: nonexistent directory
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
unlink running file </var/run/rc.igmp.run>
[SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
[rc.c::rc_start():732] Calling Start function of usb_service
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS
[SYSTEM]/usr/sbin/killall -9 hd-idle
insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists
[SYSTEM]/usr/sbin/killall -9 udhcpc
killall: hd-idle: no process killed
[SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script &
[dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started
unlink running file </var/run/rc.usb_service.run>
[rc debug]/usr/sbin/rc wifi_isolation restart
ap_name=wifi_isolation action=restart
[rc.c::rc_action():829] rc_action before add wifi_isolation - restart
 rc action <wifi_isolation @ restart> before file_lock.
 rc action <wifi_isolation @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add wifi_isolation - restart
[rc.c::rc_stop():771] Calling Stop function of wifi_isolation
[SYSTEM]/sbin/rmmod /lib/modules/wifi_isolation.ko
rmmod: /lib/modules/wifi_isolation.ko: No such file or directory
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS
[rc.c::rc_start():732] Calling Start function of wifi_isolation
[clientpacket.c::send_discover():175] Sending discover...
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB
[wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation!
unlink running file </var/run/rc.wifi_isolation.run>
[SYSTEM]/usr/sbin/rc dnrd start
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():829] rc_action before add dnrd - start
 rc action <dnrd @ start> before file_lock.
 rc action <dnrd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - start
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
unlink running file </var/run/rc.dnrd.run>
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP
[sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU>
[SYSTEM]/usr/sbin/rc route start
[rc debug]/usr/sbin/rc route start
ap_name=route action=start
[rc.c::rc_action():829] rc_action before add route - start
 rc action <route @ start> before file_lock.
 rc action <route @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add route - start
[rc.c::rc_start():732] Calling Start function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/bin/killall failover
killall: failover: no process killed
[wan/wan.c::start_wan():1513] ipv6 restart, v4 mode bridge v6 mode disable
[SYSTEM]/usr/sbin/rc ipv6 restart
[rc debug]/usr/sbin/rc ipv6 restart
ap_name=ipv6 action=restart
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ipv6 - restart
unlink running file </var/run/rc.ipv6.run>
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
[sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4>
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add ipv6 - restart
unlink running file </var/run/rc.ipv6.run>
can't find this application
[rc.c::rc_action():829] rc_action before add ipv6 - restart
 rc action <ipv6 @ restart> before file_lock.
 rc action <ipv6 @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run
block items: unlock = 3> after file_lock.

[rc.c::rc_actioninput:clear

():837] rc_action after add ipv6 - restarclamp total entry used:0
t
[rc.c::rc_stop():771] Calling Stop functitotal count:0
on of ipv6
[input str:clear

ippsd clear oldest entry
v6/ipv6.c::stop_ipv6():30] AP Mode no need ipv6.
[rc.c::rc_st proc_write_echo_chargen receive: len: 6, input: clear
ar proc_write_echo_chargen receive: clear list
t( Leaving proc_write_echo_chargen : size: 6
):732] Calling Start function of ipv6
[ipv6/ipv6.cwan interface=[eth3], index=9
::br interface=[br0], index=8
start_ipv6():102] AP Mode no need ipv6.
unlink running file </var/run/rc.ipv6.run>
ln: /tmp/www/www.eng: Read-only file system
[SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
[rc.c::rc_stop():771] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
[rc.c::rc_start():732] Calling Start function of firewall
[SYSTEM]/usr/bin/killall -14 access_logd
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():829] rc_action before add syslogd - create
 rc action <syslogd @ create> before file_lock.
 rc action <syslogd @ create lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add syslogd - create
[rc.c::rc_create():813] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
fw_pt
[SYSTEM]/usr/sbin/killall -9 usb_httpd
killall: usb_httpd: no process killed
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
ERROR: isock: Couldn't bind local address
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300&
unlink running file </var/run/rc.httpd.run>
[SYSTEM]/usr/sbin/rc dnrd start
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():829] rc_action before add dnrd - start
 rc action <dnrd @ start> before file_lock.
 rc action <dnrd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - start
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[clientpacket.c::send_discover():175] Sending discover...
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
ERROR: isock: Couldn't bind local address
unlink running file </var/run/rc.dnrd.run>
[SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null
[SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null
[clientpacket.c::send_discover():175] Sending discover...
username=admin,passwd=password
----------------
[SYSTEM]/usr/bin/killall -9 nmbd 2>/dev/null
[SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19
unlink running file </var/run/rc.lan.run>

Usage: rc [wan|service|ap name] [start|stop|restart|create]

[basic/lan_cfg.c::start_lan_ap():329] udhcpc cannot get IP, run autoip app to generate IP for br0
[SYSTEM]/usr/sbin/killall -SIGUSR2 udhcpc
[dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=17
[SYSTEM]/usr/sbin/autoip
We will test autoip: 192.168.0.100
send 0 request pkgs
send 1 request pkgs
send 2 request pkgs
We will do announce for autoip: 192.168.0.100
send 0 request pkgs
send 1 request pkgs
probe success with latest probe IP
[SYSTEM]/usr/sbin/killall -SIGUSR1 udhcpc
[dhcpc.c::renew_requested():139] Received SIGUSR1 or sig 50, state=7
[basic/lan_cfg.c::start_lan_ap():338] autoip generate a IP for br0, use it and run lan ap up
[rc debug]/usr/sbin/rc dnrd restart
ap_name=dnrd action=restart
[rc.c::rc_action():829] rc_action before add dnrd - restart
 rc action <dnrd @ restart> before file_lock.
 rc action <dnrd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 3> after file_lock.
[clientpacket.c::send_discover():175] Sending discover...
[rc.c::rc_action():837] rc_action after add dnrd - restart
[rc.c::rc_stop():771] Calling Stop function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
Notice: caching turned off[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100

Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
unlink running file </var/run/rc.dnrd.run>
[rc debug]/usr/sbin/rc httpd restart
ap_name=httpd action=restart
[rc.c::rc_action():829] rc_action before add httpd - restart
 rc action <httpd @ restart> before file_lock.
 rc action <httpd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add httpd - restart
[rc.c::rc_stop():771] Calling Stop function of httpd
killall: remote_httpd: no process killed
[rc.c::rc_start():732] Calling Start function of httpd
[sc_language.c::create_language_file():426] Create link files for <English>
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP
[sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU>
[sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4>
ln: /tmp/www/www.eng: Read-only file system
[SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewall @ restart> before file_lock.
 rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
 rc action < unlock = 3> after file_lock.
[rc.c::rc_action():837] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():829] rc_action before add firewall - restart
 rc action <firewalblock items:
l @ restart> befoinput:clear

re file_lock.
 rc action <firewall @ restart lock = 3> clamp total entry used:0
after file_lock.
[SYSTEM]/bin/ctotal count:0
p /proc/uptiminput str:clear

e psd clear oldest entry
/var/run/rc.firewall.run
 rc action < unlock  proc_write_echo_chargen receive: len: 6, input: clear
=  proc_write_echo_chargen receive: clear list
3 Leaving proc_write_echo_chargen : size: 6
> after file_lock.
[rc.c::rc_awan interface=[eth3], index=9
cbr interface=[br0], index=8
tion():837] rc_action after add firewall - restart
[rc.c::rc_stop():771] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
[rc.c::rc_start():732] Calling Start function of firewall
[SYSTEM]/usr/bin/killall -14 access_logd
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():829] rc_action before add syslogd - create
 rc action <syslogd @ create> before file_lock.
 rc action <syslogd @ create lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add syslogd - create
[rc.c::rc_create():813] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
fw_pt
[SYSTEM]/usr/sbin/killall -9 usb_httpd
killall: usb_httpd: no process killed
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300&
unlink running file </var/run/rc.httpd.run>
[SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null
[SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null
[SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null
[clientpacket.c::send_discover():175] Sending discover...
[clientpacket.c::send_discover():175] Sending discover...
username=admin,passwd=password
----------------
[SYSTEM]/usr/bin/killall -HUP nmbd
[SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19
[SYSTEM]/usr/sbin/rc usb_service restart
[rc debug]/usr/sbin/rc usb_service restart
ap_name=usb_service action=restart
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action <usb_service @ restart lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
unlink running file </var/run/rc.usb_service.run>
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action <usb_service @ restart lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
unlink running file </var/run/rc.usb_service.run>
can't find this application
[rc.c::rc_action():829] rc_action before add usb_service - restart
 rc action <usb_service @ restart> before file_lock.
 rc action <usb_service @ restart lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add usb_service - restart
[rc.c::rc_stop():771] Calling Stop function of usb_service
[SYSTEM]/etc/mtk/mt7621_smp.sh wifi
[SYSTEM]/bin/rm /etc/samba/secrets.tdb
rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
[SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
[rc.c::rc_start():732] Calling Start function of usb_service
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/sbin/killall -9 hd-idle
killall: hd-idle: no process killed
unlink running file </var/run/rc.usb_service.run>
[rc debug]/usr/sbin/rc wifi_isolation restart
ap_name=wifi_isolation action=restart
[rc.c::rc_action():829] rc_action before add wifi_isolation - restart
 rc action <wifi_isolation @ restart> before file_lock.
 rc action <wifi_isolation @ restart lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add wifi_isolation - restart
[rc.c::rc_stop():771] Calling Stop function of wifi_isolation
[SYSTEM]/sbin/rmmod /lib/modules/wifi_isolation.ko
rmmod: /lib/modules/wifi_isolation.ko: No such file or directory
[rc.c::rc_start():732] Calling Start function of wifi_isolation
[wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation!
unlink running file </var/run/rc.wifi_isolation.run>
[SYSTEM]/usr/sbin/rc dnrd start
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():829] rc_action before add dnrd - start
 rc action <dnrd @ start> before file_lock.
 rc action <dnrd @ start lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add dnrd - start
[rc.c::rc_start():732] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0   -s 8.8.8.8  -o 0 -q xxx&
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100
unlink running file </var/run/rc.dnrd.run>
[SYSTEM]/usr/sbin/rc route start
[rc debug]/usr/sbin/rc route start
ap_name=route action=start
[rc.c::rc_action():829] rc_action before add route - start
 rc action <route @ start> before file_lock.
 rc action <route @ start lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
 rc action < unlock = 4> after file_lock.
[rc.c::rc_action():837] rc_action after add route - start
[rc.c::rc_start():732] Calling Start function of route
unlink running file </var/run/rc.route.run>
[SYSTEM]/bin/killall failover
killall: failover: no process killed
[SYSTEM]/usr/sbin/brctl stp br0 off
[SYSTEM]/usr/sbin/brctl stp br0 on
sh: cannot create /proc/http_file/getLanIp: nonexistent directory
unlink running file </var/run/rc.lan.run>
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.


 • /proc/mtd • >>
# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "Bootloader"
mtd1: 00100000 00020000 "SC PID"
mtd2: 00400000 00020000 "Kernel"
mtd3: 01c00000 00020000 "Rootfs"
mtd4: 00200000 00020000 "English UI"
mtd5: 00200000 00020000 "ML1"
mtd6: 00200000 00020000 "ML2"
mtd7: 00200000 00020000 "ML3"
mtd8: 00200000 00020000 "ML4"
mtd9: 00200000 00020000 "ML5"
mtd10: 00100000 00020000 "Factory"
mtd11: 00100000 00020000 "SC Private Data"
mtd12: 00200000 00020000 "POT"
mtd13: 00200000 00020000 "Traffic Meter"
mtd14: 00200000 00020000 "DPF"
mtd15: 00200000 00020000 "SC Nvram"
mtd16: 00200000 00020000 "Ralink Nvram"
mtd17: 00200000 00020000 "Ralink Reserved"
mtd18: 00200000 00020000 "ML6"
mtd19: 00200000 00020000 "Upgrade Flag"
mtd20: 00200000 00020000 "Reserved Block3"
mtd21: 03c00000 00020000 "Reserved Block4"

Creating 22 MTD partitions on "MT7621-NAND":
0x000000000000-0x000000100000 : "Bootloader"
0x000000100000-0x000000200000 : "SC PID"
0x000000200000-0x000000600000 : "Kernel"
0x000000600000-0x000002200000 : "Rootfs"
0x000002200000-0x000002400000 : "English UI"
0x000002400000-0x000002600000 : "ML1"
0x000002600000-0x000002800000 : "ML2"
0x000002800000-0x000002a00000 : "ML3"
0x000002a00000-0x000002c00000 : "ML4"
0x000002c00000-0x000002e00000 : "ML5"
0x000002e00000-0x000002f00000 : "Factory"
0x000002f00000-0x000003000000 : "SC Private Data"
0x000003000000-0x000003200000 : "POT"
0x000003200000-0x000003400000 : "Traffic Meter"
0x000003400000-0x000003600000 : "DPF"
0x000003600000-0x000003800000 : "SC Nvram"
0x000003800000-0x000003a00000 : "Ralink Nvram"
0x000003a00000-0x000003c00000 : "Ralink Reserved"
0x000003c00000-0x000003e00000 : "ML6"
0x000003e00000-0x000004000000 : "Upgrade Flag"
0x000004000000-0x000004200000 : "Reserved Block3"
0x000004200000-0x000007e00000 : "Reserved Block4"
[mtk_nand] probe successfully!


Reviews

Images